..
Comment archives
recent comments are here
..
Comment archives
recent comments are here
.
| "Hey guys - Got my Newer 300/150 on Tuesday as promised and popped into my 9600/200. Took less than 10 minutes and I was up and running... or should I say screaming! Very solid card and software with absolutely no problems so far. I have 400MB of RAM, a ton of extensions and use my Mac 10 hours a day doing graphic design... this is sweet! Haven't been successful at clocking it any faster but will try again this weekend. At this speed I can't really ask for much more... Thanks a ton. MacCPU is the best! Sincerely" Mike Buettner, CA |
| "Bob and Barb, Thanks. After three Mactell cards and one Railgun card, I finally got a G3 card to boot in my PTP 225 on the first try. Thanks for the Newer 275/275/1 card. Thanks for your help, correspondence and patience. If you are ever close to Lake Tahoe, NV, you are welcome to stay at my house." Mark |
| "Barb, Received the Little Smoker this morning... An easy install and now my 9500 runs with the best of them! Thanks, Jim." Jim Anders PA |
| "I got my G3 220 and the extra 32 MB of RAM - it is awsome. Thanks for the great service! I know a lot of Mac owners and I'm sending them all to you for memory and upgrades. This is the first time that I've ordered memory or other components that actually worked flawlessly after a 10 minute, 8 step installation. I appreciated the fact that all I had to do was tell you the processor speed I wanted and what kind of machine I have and you made sure I got components that would work in my machine. Thanks again." Cory Stokes, UT |
| "...On a final note: Thanks for your excellent service once again. I have long been ordering upgrades and software online and among all the different resellers i have done business with - MacCPU's service is the best! Also, thanks for the prompt reply... what time was it went u replied my first e-mail? If my 'Map' control panel is accurate, it must have been about 11.30pm or so in Miami! Alex, Malaysia |
| "card arrived..installation a piece of cake... thanks for the book.. and the other excellent software that came along... best wishes" Mel Martin, BBC London |
| "We're screaming! thanks." Mike Moose, OH |
| "I'm in heaven! My computer is fast, and it is obeying my every command with nary a protest such as a freeze or a crash. It's been running perfectly all weekend. This thing acts like someone who's hyperactive after drinking 2 pots of coffee! A whole new era has opened up for me. Thanks for your help in getting the card to me." Pat Whitty, TX |
| "Barbara, Thanks for the info. The little smoker is installed and working as we speak. This is my first experience with your company and I am 100% satisfied with the ordering, delivery and electronics. You and your people just moved to the top of the list. Your friend and mine, Mark." Mark Hargrave, CA |
| "Barb, thank you for all your help. Our package arrived yesterday (Monday), installed without a hitch and was up and running in 10 minutes. Great service from you and your team, and I will be back for more CPUs soon! Thanks again." Neil Cowley, New Zealand |
| "It was so very nice to hear your lovely voice and receive such wonderful service. You are a dear!! I can barely wait to get the G3 card, memory and whatever the "surprise" is." Jeff S, Arizona |
"My 1MB L2 cache DIMM arrived this morning
and is happily chugging away in my PowerWave 120 w/Newer MAXpowr 200MHz
CPU upgrade. I had been running the 210/60 settings on the CPU card without
any L2 cache installed. Upon installing the cache DIMM I had to take it
down to 200/50 but still got nearly a 200% performance boost over the previous
settings. Mac Bench 4.0 clocks in at 509 processor/647 fpu." Chris
Colando, Atlanta, GA "After installing the MP400MHz card in my 9500/132 I don't know what is more impressive, the fact that it only took 6.5 min to install with no glitches, or the fact that it cut over 2 hours off one of my most complex calculations!!" Todd Johnson, Los Angeles, CA "I upgraded my 9500/132 to the MP 360 - and a Gaussian blur that used to take over 40 minutes on the 9500 took only 6 minutes with the MAXpowr MP 360 : Awesome" Kevin G, Brooklin, MA "In Bryce 2 at 640 x480 rendered on my 8500/150MHz it took 3mins 18secs and with the MAXpowr 225MHz set at 240MHz/60MHz Bus speed it took 1min 18secs. In ID I rendered an animation, ray traced, at 320 x240, and it took less than a minute for each frame. I think this is almost twice as fast as the 150MHz!!" S.P, Bellefont, PA "I recently purchased the 225 MHz CPU upgrade. It is amazing how much faster my 7600 is." Kevin DeFreest, Oakland, NJ "...for anyone who is considering purchasing
products from MacCPU. I was very pleased at their assistance with helping
me get my machine up to speed. I am recommending them to all my friends
and business associates who want to also increase the speed of their machines.
I was impressed how they have researched and tested various boards and only
provided the best solution for upgrading my 8500/120 to a stable
speed of 225MHz with a 56.25 MHz bus. I did many 'before and
after' benchmarks and estimate that I will be 40 - 50% more productive each
workday. "...your site offers more information about
the relationship between bus speed and processor speed than I've been able
to find anywhere! Thanks for the education." J Cabannis, Texas "I've been playing around with all my new programs seeing the GREAT improvement with the 200MHz card. Your service has been nothing short of exceptional... " S Saeed, Kent, OH "Thanks very much for the extremely terrific service from the order notification to the tracking info. I've just completed installation - took me around 10 minutes total time on my 8500 (what took longer was pulling off all my connections so that I could easily open the case, than setting the dip switches and actually installing the card). Craig Oshiro, Hawaii |